LISTED PRICE

TECHNICAL SPECIFICATIONS

Volumetric mass	≥ 1.5 g/cm 3 (bulk density)		TCVN 7572-6:2006
Consumption density	3-6 kg Mizone ® Floor Chapdur per m 2 4 kg/m 2 for normal load bearing areas 5 – 6 kg/ m2 for heavy load areas
Chemical resistance	Mizone ® Floor Chapdur once cured will achieve a hard, dense surface with high abrasion resistance. The floor surface will have the same chemical limitations as other cementitious products.
Compressive strength (28 days)	≥ 60 N/mm 2	TCVN 3121-11:2003
Abrasion resistance	< 0.5 g/cm 2	TCVN 3114:1993
Waiting time	Depending on ambient temperature and type of cement used in the floor, waiting time is:2-3 days for foot traffic For light duty vehicles 7-10 days For normal circulation 28 days

APPLICATION

This is one of the products for the special floor system of mizone waterproofing . To reinforce the floor surface and concrete slabs, to increase the abrasion resistance and thus minimize the formation of dust.

Suitable for floors subject to severe mechanical wear and requiring a particularly hard coating such as:

Storehouse

Traffic routes

Mechanical workshop

Parking lot

Warranty stations

Garages etc…

FEATURES/ ADVANTAGES

Mizone ^® Floor Chapdur offers the following properties:

Natural color

High abrasion resistance

Reduce dust on the surface

Increased impact resistance

Increased oil resistance

Easy to construct

No need to apply a rock hard screed

Has a smooth finish if troweled properly.

CONSTRUCTION INSTRUCTIONS

SURFACE QUALITY / PRE-TREATMENT:

Immediately after the concrete surface reaches plasticity (after the concrete has drained but before it has begun to set) smooth the newly poured concrete surface and level the surface with a tamping scale.

CONSTRUCTION:

Sprinkle the Mizone ^® Floor Chapdur mixture “by hand” onto the still wet and leveled concrete surface at a rate of 3-6 kg/m ² . Allow the Mizone ^® Floor Chapdur to absorb moisture from the concrete surface and while still wet, use a floor trowel to smooth the Mizone ^® Floor Chapdur surface.

FLATTING:

As soon as the mixture becomes plastic or when it is about to set, carry out the first leveling with a trowel running at low speed but with a metal blade attached at a minimum angle. The final leveling (if necessary) should be carried out some time later but with the trowel running at high speed.

MAINTENANCE:

Mizone ^® Floor Chapdur mixed surfaces must be protected from rapid water loss as this may cause surface cracking. An approved curing system must therefore be applied.

CONSTRUCTION NOTES/LIMITATIONS:

When applying the product, dry powder form, do not do so during strong winds.

Properties of the concrete ingredients such as water content and cement quality may cause slight colour variations. Some colour variation during the drying of the concrete is normal for this system and is acceptable.

Dry shake floor hardeners will produce a concrete finish that will have some color variation throughout the entire surface. This is due to the natural variations in the concrete on which the product has been applied.

At high relative humidity, phenomena such as water separation, slow curing, prolonged finishing time and slow hardening of concrete are likely to occur. 

HEALTH AND SAFETY INFORMATION

LEGAL NOTE

The information, and in particular the recommendations relating to the application and end-use of Mizone ^® Floor Chapdur products, are given in good faith based on Mizen's current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with the recommendations of Mizone ^® Floor Chapdur. In practical application, differences in materials, substrates and actual site conditions do not imply any warranty in respect of fitness for a particular purpose, nor can any liability in respect of us be inferred from this information or from any written recommendations or from any other advice offered. It is up to the user of this product to test whether the product is suitable for the intended application. Mizen reserves the right to change the characteristics of its products. The proprietary rights of third parties must be noted. All orders are accepted only on the basis of our current Terms of Sale. The user must always refer to the latest Technical Data Sheet for the product. We will provide these documents upon request.

In addition, there are many other waterproofing products that Bac Minh Hai is providing to customers.

Product Catalog documents are continuously updated here.