Mizone Monotop R is a non-shrink cementitious repair mortar, reinforced with fiber combined with improved polymers and other special additives.

LISTED PRICE

PRODUCT NAME	Unit	SPECIFICATIONS	UNIT PRICE (VND)
Mizone Monotop R High-tech Polymer Modified Repair Mortar	Bag	25 Kg	1,050,000

APPLICATION

• Quick repair for vertical and horizontal surfaces of mortar and concrete above or below ground.
• Filling/repair mortar for areas with voids, honeycombs etc.
• Repair of damaged concrete peeling due to corroded steel reinforcement.
• Repair while increasing resistance to oil, chemicals, waste etc.

FEATURES/ ADVANTAGES

• Fast and easy construction.
• Just add clean water when using.
• Adjustable viscosity
• Compatible with the thermal expansion properties of concrete.
• Chloride free, non-corrosive, non-toxic.
• Combined with fibers to prevent micro cracks.
• Minimizes shrinkage tendency.
• High adhesive strength.
• Significantly reduces water and carbon dioxide permeability.
• Good Sulfate resistance.
• Increased resistance to oil and chemicals.

SPECIFICATIONS
Volumetric mass	~1.02 kg/l (bulk density of powder)~2.15 kg/l (bulk density of fresh mortar)
Mixing ratio	Water : Mizone ® Monotop powder R = 1 : 7.15 – 7.40 (by weight)Water : Mizone ® Monotop powder R = 1 : 4.95 – 5.10 (by volume) About 3.40 – 3.50 liters of clean water for a 25 kg bag.
Standard	1 bag gives about 13.3 liters of mortar. About 75 bags are needed for 1 m3 of mortar.
Time allowed for construction	~ 30 minutes (at 27 0 C / 65% ambient humidity)
Initial setting time (27 0 C)	5 – 9 hours	ASTM C403:2016
Final setting time (27 0 C)	8 – 12 hours
Compressive strength	≥ 15 N/mm 2 (3 days)	TCVN 3121-11:2003
	≥ 40 N/mm 2 (28 days)
Flexural strength	≥ 6 N/mm 2 (28 days)
Bond strength (28 days)	≥ 1.5 N/mm 2 (on concrete surface with bonding layer) TCVN 9349:2012
Thickness of each layer	Minimum 5 mm Maximum 30 mm
Construction temperature	Minimum 6 0 CMaximum 40 0 ​​C

CONSTRUCTION INSTRUCTIONS

Surface preparation:

The surface must be thoroughly saturated with water but without standing water. This means that the surface must be thoroughly saturated and free of any cement slurry or dust created during surface preparation. The steel reinforcement must be cleaned of all rust and primed with 2 coats of Mizone ^® Monotop 610.

Primer:

Apply 2 coats of Mizone Monotop 610 with a brush onto the prepared surface (see Mizone ^® Monotop 610 instructions for use).

Mix:

Mizone ^® Monotop R must be mixed in a clean container using an electric mixer at low speed (maximum 500 rpm). Add the required amount of water (3.4 – 3.5 litres of water for 25 kg of Mizone ^® Monotop R) to a clean container and then slowly add Mizone ^® Monotop R while continuing to mix. Mix thoroughly for at least 3 minutes.

Construction:

Apply the bonding layer to the dry, saturated surface with a brush. Then, while the bonding layer is still wet, apply the well-mixed mortar to the surface, using a plastering method to fill in the holes. Compact thoroughly. Compact the material at the edges of the repair and gradually work towards the center. If the repair depth exceeds 20 mm, apply in several layers and make sure the previous mortar layer is hard and rough for good adhesion.

Maintenance:

To achieve the full properties of cementitious materials, curing is of utmost importance. In warm, windy weather, normal curing measures (using polythene sheets or damp burlap) should be taken to prevent the mortar from drying out too early.

Toilet:

Clean uncured Mizone ^® Monotop R products from equipment and tools with water. Once cured, the product can only be removed by mechanical means.

Construction notes/limitations:

Mizone Monotop R mortar wetted during the initial curing stage may produce white patches on the surface but this does not affect the long term properties of the mortar.

IMPORTANT ATTENTION

Minimum working temperature is 10 ^o C. If the working temperature is lower than 20 ^o C, the setting time and strength achieved will be slower.

A normal curing period of at least 3 days must be observed where mortar is exposed.

BASIC PRODUCT INFORMATION

All specifications in this document are based on laboratory results. Actual measurement data may vary depending on the specific case.

LOCAL RESTRICTIONS

Please note that product performance may vary from country to country due to local requirements. Please refer to local product specifications for exact descriptions of application areas.

ECOLOGY, HEALTH AND SAFETY

Ecology: Do not dispose of into water sources.

Transport: Non-hazardous.

Waste disposal: According to local regulations.

Important Note:

Mizone Monotop R is a cement-based product and is therefore alkaline. Appropriate precautions should be taken to minimize skin contact. If product gets into eyes or mucous membranes, rinse with clean water and seek medical attention immediately.

LEGAL NOTE

The information, and in particular the recommendations relating to the application and end-use of Mizone ^® Monotop R products, are given in good faith based on Mizen's current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with the recommendations of Mizone ^® Monotop. In practical application, we give no warranty of fitness for a particular purpose due to differences in materials, substrates and actual site conditions, nor can any legal obligation in respect of us be implied from this information or from any written recommendations, or from any advice offered. The user of this product must test the product to determine whether it is suitable for the intended application. Mizen reserves the right to change the characteristics of its products. The proprietary rights of third parties must be noted. All orders are accepted only on the basis of our current Terms of Sale. Users should always refer to the product's latest Technical Data Sheet, which we will provide upon request.

If you need more information, please visit: mizone price list so we can provide you with full information.