LISTED PRICE

APPLICATION

Mizone ^® Top Seal-107 is used for internal and external waterproofing, repair work and protection against frost and de-icing agents. Application areas:

Drinking water tank, fire water tank

Basement

Terrace and balcony

Bridge

Retaining wall

Filling of stable developed hairline cracks.

FEATURES/ ADVANTAGES

Mizone ^® Top Seal-107 offers the following properties:

Prefabricated components

Easy to mix and easy to apply Has the consistency of oil paste

Good adhesion to solid surfaces.

Waterproof

Is an effective barrier against carbonation

Non-toxic

Non-corrosive

Light elastic

Can be applied by spraying.

CONSTRUCTION INSTRUCTIONS
Mixing ratio	Component A : B = 1 : 4.0 (by mass)Creating crack bridges: Component A : B = 1 : 1 – 2.5 (by mass)
Standard	Waterproofing bathroom, terrace, balcony: ~1.5 – 2.0 kg/m 2 /layer Waterproofing for places with water pressure up to 1m: ~1.5 – 2.0 kg/m 2 /layer Waterproofing for places with water pressure above 1m or frost resistance: ~2.0kg/m 2 /layer Always apply at least 2 coats. In areas with severe water pressure, 3 coats are required. Approximately 75 bags are required for 1 m3 of mortar.
Surface temperature	Min +8 o C Max +40 o C
Thickness of each layer	Minimum 5 mm Maximum 30 mm
Construction time	~ 30 minutes (at 27 o C / 65% ambient humidity)

CONSTRUCTION INSTRUCTIONS

SURFACE QUALITY / PRE-TREATMENT

Concrete and mortar surfaces must be clean and free from oil, grease and other loose materials. Absorbent surfaces must be thoroughly saturated before applying the first coat of Mizone ^® Top Seal-107.

MIX

Under normal conditions, when all 2 components are mixed together, a thick oil paste is formed. Mix in a clean container by slowly adding the powder component to the liquid component and mixing thoroughly with a low speed electric mixer (less than 500 rpm).

CONSTRUCTION

Apply the first coat of Mizone ^® Top Seal-107 onto the fully saturated surface by brush, wire brush or trowel.

Allow the product to cure for approximately 4-8 hours at temperatures above 20 ^o C before applying the second coat. When applying on floors, to avoid the risk of damaging the first coat, it is recommended to apply the second coat after approximately 24 hours. If the second coat is applied after 12 hours or more, it is necessary to moisten the first coat by suitable means, such as spraying. Please contact Mizen Technical Department for further details.

CURING / CUREMENT

Like other cement-based products, it is essential to cure Mizone ^® Top Seal-107 immediately after application, avoiding direct sunlight, strong winds and frost for about 3 to 5 days to ensure the material is fully hydrated and to limit small cracks.

Use plastic sheeting for maintenance or other approved measures.

CLEANING TOOLS

Clean all tools and equipment with clean water immediately after use. Cured material can only be cleaned by mechanical means.

IMPORTANT ATTENTION

Do not apply Mizone ^® Top Seal-107 at a rate of more than 4 kg/m ² per application.

Mizone ^® Top Seal-107 is not intended for decorative surfaces and may show white flecks in humid weather conditions. This does not affect the waterproofing properties.

Allow to dry for at least 3 days before soaking in water.

Always use Mizone ^® Latex or Mizone ^® Latex Plus bonding slurry to prevent blistering when applying the finishing/protective mortar over the waterproofing layer.

Always construct a sample area before mass construction.

Always refer to the latest technical documentation.

BASIC PRODUCT INFORMATION

All specifications in this document are based on laboratory results. Actual measurement data may vary depending on the specific case.

LOCAL RESTRICTIONS

Please note that product performance may vary from country to country due to local requirements. Please refer to local product specifications for exact descriptions of application areas.

ECOLOGY, HEALTH AND SAFETY

For information and advice on the safe use, storage and disposal of chemical products, users should consult the most recent Material Safety Data Sheet for physical, ecological, toxicological and other relevant safety data.

LEGAL NOTE

The information, and in particular the recommendations relating to the application and end-use of Mizone ^® Top Seal-107 products, are given in good faith based on Mizen's current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with the recommendations of Mizone ^® Top Seal-107. In practical application, we do not warrant that the products will be of a particular type or that they ... All orders are accepted only on the basis of our current Terms of Sale. The user must always refer to the latest Technical Data Sheet for the product. We will provide these documents upon request.